Carnot cycle Totally Explained

Everything about The Carnot Cycle totally explained

The Carnot cycle is a particular thermodynamic cycle, modeled on the hypothetical Carnot heat engine, proposed by Nicolas Léonard Sadi Carnot in 1824 and expanded upon by Benoit Paul Émile Clapeyron in the 1830s and 40s. Every thermodynamic system exists in a particular state. A thermodynamic cycle occurs when a system is taken through a series of different states, and finally returned to its initial state. In the process of going through this cycle, the system may perform work on its surroundings, thereby acting as a heat engine.
A heat engine acts by transferring energy from a warm region to a cool region of space and, in the process, converting some of that energy to mechanical work. The cycle may also be reversed. The system may be worked upon by an external force, and in the process, it can transfer thermal energy from a cooler system to a warmer one, thereby acting as a Heat Pump rather than a heat engine.
The Carnot cycle is the most efficient cycle possible for converting a given amount of thermal energy into work or, conversely, for using a given amount of work for refrigeration purposes.

The Carnot cycle

The Carnot cycle when acting as a heat engine consists of the following steps:

Reversible isothermal expansion of the gas at the "hot" temperature, T_H (isothermal heat addition). During this step (A to B on Figure 1) the expanding gas causes the piston to do work on the surroundings. The gas expansion is propelled by absorption of heat from the high temperature reservoir.
Isentropic (Reversible adiabatic) expansion of the gas. For this step (B to C on Figure 1) we assume the piston and cylinder are thermally insulated, so that no heat is gained or lost. The gas continues to expand, doing work on the surroundings. The gas expansion causes it to cool to the "cold" temperature, T_C.
Reversible isothermal compression of the gas at the "cold" temperature, T_C. (isothermal heat rejection) (C to D on Figure 1) Now the surroundings do work on the gas, causing heat to flow out of the gas to the low temperature reservoir.
Isentropic compression of the gas. (D to A on Figure 1) Once again we assume the piston and cylinder are thermally insulated. During this step, the surroundings do work on the gas, compressing it and causing the temperature to rise to T_H. At this point the gas is in the same state as at the start of step 1.

Properties and significance

The temperature-entropy diagram

The behavior of a Carnot engine or refrigerator is best understood by using a temperature-entropy (TS) diagram, in which the thermodynamic state is specified by a point on a graph with entropy (S) as the horizontal axis and temperature (T) as the vertical axis. For a simple system with a fixed number of particles, any point on the graph will represent a particular state of the system. A thermodynamic process will consist of a curve connecting an initial state (A) and a final state (B). The area under the curve will be:
ť

Q=int_A^B T,dS
quadquad(1)

which is the amount of thermal energy transferred in the process. If the process moves to greater entropy, the area under the curve will be the amount of heat absorbed by the system in that process. If the process moves towards lesser entropy, it'll be the amount of heat removed. For any cyclic process, there will be an upper portion of the cycle and a lower portion. For a clockwise cycle, the area under the upper portion will be the thermal energy absorbed during the cycle, while the area under the lower portion will be the thermal energy removed during the cycle. The area inside the cycle will then be the difference between the two, but since the internal energy of the system must have returned to its initial value, this difference must be the amount of work done by the system over the cycle. Mathematically, for a reversible process we may write the amount of work done over a cyclic process as:
ť

W = oint PdV = oint (Q-dU)= oint (TdS-dU)
quadquadquadquad(2)

Since dU is an exact differential, its integral over any closed loop is zero and it follows that the area inside the loop on a T-S diagram is equal to the total work performed if the loop is traversed in a clockwise direction, and is equal to the total work done on the system as the loop is traversed in a counterclockwise direction.

The Carnot cycle

Evaluation of the above integral is particularly simple for the Carnot cycle. The amount of energy transferred as work is ť

W = oint PdV = (T_H-T_C)(S_B-S_A)

The total amount of thermal energy transferred between the hot reservoir and the system will be ť

Q_H=T_H(S_B-S_A),

and the total amount of thermal energy transferred between the system and the cold reservoir will be ť

Q_C=T_C(S_B-S_A),

.

The efficiency

eta

is defined to be:
ť

eta=frac TdS

at which heat is input and output, respectively. Replace T_H and T_C in Equation (3) by <T_H> and <T_C> respectively.
For the Carnot cycle, or its equivalent, <T_H> is the highest temperature available and <T_C> the lowest. For other less efficient cycles, <T_H> will be lower than T_H, and <T_C> will be higher than T_C. This can help illustrate, for example, why a reheater or a regenerator can improve thermal efficiency. ť See also: Heat Engine efficiency and other performance criteria

Further Information

Get more info on 'Carnot Cycle'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://carnot_cycle.totallyexplained.com">Carnot cycle Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.